ENFlat solar panelsNEO 2.1 / SUN 211Installation andService ManualRoof-integralInstallation20° to 65°300021356-001-F
4 Installation4.1 Regulations governing installationCAUTION4 The installation must comply in all matters to thestandards and rules which govern the wo
4.2 Package listM001801-BER45 ER193(5x)(5x)(2x)(2x)M001802-BER194 ER195(10x)(10x)(4x)(4x)(5x)(5x)(2x)(2x)NEO 2.1 / SUN 211 4. Installation30/11/2011
M001803-BER47 ER48(12x)(2x)(1x)(20x)(12x)(10x)(10x)(10x)M001804-BER49(2x)(2x)(1x)(2x)(2x)30ER236C003463-B4. Installation NEO 2.1 / SUN 2111130/11/2011
Pack no. Article no. Description Packages needed to construct the installation dependingon the number of solar collectors1 2 3 4 5ER 45 100013471 Sola
4.3 Main dimensionsASolar collector inletZSolar collector outletESolar sensor probeM001740-A1060113,5 113,5175,537196070321 2 314. Installation NEO 2.
4.4 Installation diagrams4.4.1. Vertical assembly, juxtaposedConnection for 1 to 5 collectors.CAUTIONPlace the collector sensor on the flow side of th
4.4.2. Example of an installation4Pressure gauge9Isolating valve17Drain cock57Domestic hot water outlet61Thermometer84Stop valve with lockable nonretu
4.5 Assembling the solar collectors4.5.1. WarningM001748-ANEO 2.1 / SUN 211 4. Installation30/11/2011 - 300021356-001-F16
4.5.2. Tools requiredM001719-B10 104. Installation NEO 2.1 / SUN 2111730/11/2011 - 300021356-001-F
4.5.3. DimensionsAExisting battenZFlow batten to be fitted width 90 mm suppliedEFastening batten to be fitted suppliedRFastening batten to be fitted n
Contents1 Introduction ...41.1 Symbols used ...
CAUTIONBattens Z, E and R must be of the same thickness asthe existing battens.4.5.4. Clearance to allow forNumber of panels 1 2 3 4 5Size A 1600 2660
4.5.5. Fitting the battensAThe new fastening battens must be of the same thicknessas the roof battens.BSecure the battens using the screws provided.M0
4.5.6. Mounting for an installation with 2collectorsnPositioning the solar collectorsAScrew the lower fastening lugs onto the bottom batten.BPosition
nFitting the intermediary seals and clips1. Fit the seal, without the clamp, into the groove along the entireheight of the 2 collectors.2. Glue the in
nAssembling and securing the 2 collectorsAFit the second collector alongside the first and securethem.C003582-AAAAAA4. Installation NEO 2.1 / SUN 2112
nFitting the upper seals and clips1. Fit the seal, without the clamp, into the upper groove on the 2collectors.2. Glue the flat seal along the entire
nWaterproofing the connection between the 2 collectors1. Glue the BUTYL strip to the intermediary clips, leaving 3 mmclearance.2. Squeeze silicone on
nConnecting the solar collectorsCAUTIONInstall the temperature sensor in the sensor tube on thesolar collector, at the flow end of the bank of collect
nPassing Pipes and Cable through the RoofAScenario with two overlapping sheets of film under theroofBScenario with a single sheet of film under the ro
nFitting the lower flat sealFit the flat seal along the lower part of the 2 collectors.C003461-DNEO 2.1 / SUN 211 4. Installation30/11/2011 - 3000213
4.7 Filling the system ...615 Commissioning ...
nMounting the lower roofing platesCAUTIONIf the collectors are mounted with the flow and returnconnections at the bottom, reposition and tighten thefi
nMount the side roofing platesM001729-EABCDEFGHGHIINEO 2.1 / SUN 211 4. Installation30/11/2011 - 300021356-001-F30
nFitting the foam sealC003462-B4. Installation NEO 2.1 / SUN 2113130/11/2011 - 300021356-001-F
nMounting the upper roofing platesCAUTIONIf the collectors are mounted with the flow and returnconnections at the top, reposition and tighten the fitt
nFitting the fastening lugs and the tile restsC003587-AA A B-CAABCB-CA4. Installation NEO 2.1 / SUN 2113330/11/2011 - 300021356-001-F
nPut the tiles in placeCAUTIONIf the tip of the tile is resting on the side roofing plates, it isnecessary to cut it to size to ensure that the tile i
4.5.7. Mounting for an installation with 3 to 5collectorsnPositioning the solar collectorsAScrew the lower fastening lugs onto the bottom batten.BPosi
nFitting the intermediary seals and clips1. Fit the seal, without the clamp, into the groove along the entireheight of the 2 collectors.2. Glue the in
nAssembling and securing the 3 collectorsAFit the second collector alongside the first and securethem.C003580-AAAAAA4. Installation NEO 2.1 / SUN 2113
nFitting the upper seals and clips1. Fit the seal, without the clamp, into the upper groove on the 2collectors.2. Glue the flat seal along the entire
330/11/2011 - 300021356-001-F
nWaterproofing the connection between the 3 collectors1. Glue the BUTYL strip to the intermediary clips, leaving 3 mmclearance.2. Squeeze silicone on
nConnecting the solar collectorsCAUTIONInstall the temperature sensor in the sensor tube on thesolar collector, at the flow end of the bank of collect
nPassing Pipes and Cable through the RoofAScenario with two overlapping sheets of film under theroofBScenario with a single sheet of film under the ro
nFitting the lower flat sealFit the flat seal along the lower part of the 3 collectors.C003471-DNEO 2.1 / SUN 211 4. Installation30/11/2011 - 3000213
nMounting the lower roofing platesCAUTIONIf the collectors are mounted with the flow and returnconnections at the bottom, reposition and tighten thefi
nMount the side roofing platesM001820-CABCDEFGHGHGHIIINEO 2.1 / SUN 211 4. Installation30/11/2011 - 300021356-001-F44
nFitting the foam sealC003472-B4. Installation NEO 2.1 / SUN 2114530/11/2011 - 300021356-001-F
nMounting the upper roofing platesCAUTIONIf the collectors are mounted with the flow and returnconnections at the top, reposition and tighten the fitt
nFitting the fastening lugs and the tile restsM001824-CAA A B-C-DBCDAAB-C-D4. Installation NEO 2.1 / SUN 2114730/11/2011 - 300021356-001-F
nPut the tiles in placeCAUTIONIf the tip of the tile is resting on the side roofing plates, it isnecessary to cut it to size to ensure that the tile i
1 Introduction1.1 Symbols usedIn these instructions, various danger levels are employed to draw theuser's attention to particular information. In
4.5.8. Mounting for an installation with 1 collectornInstalling the solar collectorAScrew the lower fastening lugs onto the bottom batten.BFit the col
nFitting the seal and the upper clip1. Glue the flat seal.2. Fit the upper clip using the mallet.C003464-BA12122ANEO 2.1 / SUN 2114. Installation30/11
nConnecting the solar collectorCAUTIONInstall the temperature sensor in the sensor tube on thesolar collector.The transfer of heat between the sensor
nPassing Pipes and Cable through the RoofAScenario with two overlapping sheets of film under theroofBScenario with a single sheet of film under the ro
nFitting the lower flat sealC003473-C4. Installation NEO 2.1 / SUN 2115330/11/2011 - 300021356-001-F
nFitting the lower roofing plateCAUTIONIf the collectors are mounted with the flow and returnconnections at the bottom, reposition and tighten thefitt
nMount the side roofing platesM001819-BABCDEF4. Installation NEO 2.1 / SUN 2115530/11/2011 - 300021356-001-F
nFitting the foam sealC003465-BNEO 2.1 / SUN 211 4. Installation30/11/2011 - 300021356-001-F56
nMounting the upper roofing plateCAUTIONIf the collectors are mounted with the flow and returnconnections at the top, reposition and tighten the fitti
nFitting the fastening lugs and the tile restsM001823-CAA A BBAABNEO 2.1 / SUN 211 4. Installation30/11/2011 - 300021356-001-F58
1.2 General1.2.1. Manufacturer's liabilityOur products are manufactured in compliance with the requirementsof the various applicable European Dir
nPut the tiles in placeCAUTIONIf the tip of the tile is resting on the side roofing plates, it isnecessary to cut it to size to ensure that the tile i
4.6 Hydraulic connections4.6.1. Connection dimensionsNumber of panels Size(mm)Maximum length(Outlet + Return)2 14-15 40 m3 14-15 40 m4 16-18 40 m5 16-
4.6.3. Pipe insulationCAUTIONTo protect the insulation against mechanical damage, birdpecking and UV light, add extra protection for the heatinsulatio
To prevent damage to the collectors and their connections by frostand corrosion, it is essential that a high quality heat transporting fluidbe used to
5 Commissioning5.1 Check points before commissioning4 Check the solar collectors and their fastenings.4 Fill the installation with water and check hyd
6 Checking and maintenance6.1 General instructionsCAUTION4 Maintenance operations must be done by a qualifiedengineer.4 An annual inspection is compul
7 Spare parts7.1 Spare partsSpare parts list reference: 300021356-002-CM002124-CER47 ER48(12x)(3x)(2x)(20x)(10x)(10x)1243M002125-CER49 ER45(2x)(3x)(2x
Markers Reference Description ER 471 200017411 Screws ER 482 200016005 Top tie plate NEO collector3 200016004 Bottom tie plate NEO collector4 2000
© CopyrightAll technical and technological information contained in these technical instructions,as well as any drawings and technical descriptions su
This appliance is not intended to be used by persons (includingchildren) whose physcial, sensory or mental capacity is impaired orpersons with no expe
2 Safety instructions andrecommendations2.1 Safety instructionsDANGERThe permissible roof load of the building must not at anytime be exceeded. If nec
3 Description3.1 Operating principleThe short-wave solar radiation (sunlight) striking the solar panel isconverted into heat by the selective coating
Comments to this Manuals